多孔板结冰自强化效应对水升华器性能的影响

doi:10.7527/S1000-6893.2018.22046

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

多孔板结冰自强化效应对水升华器性能的影响

刘畅, 宁献文, 苗建印, 王玉莹, 吕巍, 王录

北京空间飞行器总体设计部空间热控技术北京市重点实验室, 北京 100094

收稿日期:2018-01-25 修回日期:2018-02-19 出版日期:2018-09-15 发布日期:2018-04-11
通讯作者: 宁献文 E-mail:ningxianwen@163.com
基金资助:
国家科技重大专项；国家自然科学基金（11472040）

Influence of self-strengthening effect of porous plate icing on water sublimators' performance

LIU Chang, NING Xianwen, MIAO Jianyin, WANG Yuying, LYU Wei, WANG Lu

Beijing Key Laboratory of Space Thermal Control Technology, Beijing Institute of Spacecraft System Engineering(ISSE), Beijing 100094, China

Received:2018-01-25 Revised:2018-02-19 Online:2018-09-15 Published:2018-04-11
Supported by:
National Science and Technology Major Project; National Natural Science Foundation of China (11472040)

摘要/Abstract

摘要： 水升华器是一种利用水作为消耗性介质的相变散热装置，在航天器热控及生保系统中得到了广泛应用。在水升华器启动及运行过程中多孔板内部发生的结冰膨胀现象会对多孔板微观结构进行再加工；由于形变硬化效应，水升华器多次工作后，多孔板的塑性将逐渐降低，结构参数将逐渐固化，将这一过程定义为多孔板的自强化。而多孔板微观结构的变化，将对水升华器防击穿能力、稳态散热功率等宏观性能产生影响。在对水升华器工作机理进行分析的基础上，从微观角度定性研究了水升华器多孔板的结冰自强化机理，并针对自强化效应对水升华器宏观性能的影响开展了实验研究。结果表明：对于本文结构的水升华器，在同一条件下，稳态散热功率随着启动次数的增加而减小，且每次减小的幅度逐渐降低，在启动3~4次后稳态散热功率逐渐趋于稳定。由实验数据得到了水升华器稳态散热功率与启动次数之间的拟合关系式；渗透率越大的多孔板，水升华器工作过程对多孔板的再加工程度更大，因而自强化效果更明显；自强化效应还可以提高水升华器的防击穿能力。研究结果为探月三期工程嫦娥五号探测器提供了一定的设计依据。

关键词: 水升华器, 多孔板, 自强化效应, 结冰, 航天器热控制

Abstract: The water sublimator is a heat rejection device widely used in the spacecraft thermal control system, which uses water as the consumptive medium by taking advantage of the sublimation phase change of water. During the startup and operation processes of the water sublimator, frost expansion in the porous plate will reshape the microscopic structure of the plate. Due to the effect of strain hardening, the plasticity of the porous plate will decrease and the structural parameters will be fixed after the water sublimator operates for many times, which is defined here as self-strengthening of the porous plate. As a consequence, the macroscopic performances of the water sublimator, e.g. steady-state heat rejection and ability of anti-breakthrough will be affected. In this paper, experimental research on self-strengthening effect of the porous plate on the water sublimator is carried out. The results show that for the specific water sublimator structure involved in this paper, the steady-state heat rejection decreases with the increase of the times of startup under the same condition, and the decrease rate slows down gradually. The steady-state heat rejection of the water sublimator is stabilized after 3-4 times of startup. A fitting formula that describes the relationship between steady-state heat rejection and times of startup is provided. The effect of self-strengthening behaves more notably as the permeability of the porous plate increases, and the effect can improve the anti-breakthrough ability of the plate. This research can offer some references for the design of the third mission of the moon exploration of China.

Key words: water sublimators, porous plate, self-strengthening effect, icing, spacecraft thermal control

中图分类号:

刘畅, 宁献文, 苗建印, 王玉莹, 吕巍, 王录. 多孔板结冰自强化效应对水升华器性能的影响[J]. 航空学报, 2018, 39(9): 122046-122053.

LIU Chang, NING Xianwen, MIAO Jianyin, WANG Yuying, LYU Wei, WANG Lu. Influence of self-strengthening effect of porous plate icing on water sublimators' performance[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(9): 122046-122053.

参考文献

[1] 王玉莹, 钟奇, 宁献文, 等. 水升华器空间应用研究[J]. 航天器工程, 2013, 22(3):105-112. WANG Y Y, ZHONG Q, NING X W, et al. Overview of space application and development of water sublimator[J]. Spacecraft Engineering, 2013, 22(3):105-112(in Chinese).
[2] 丰茂龙, 黄家荣, 范含林, 等. 美国舱外航天服热控技术研究进展[J]. 载人航天, 2011, 16(3):36-41. FENG M L, HUANG J R, FAN H L, et al. Development of thermal control technology of extravehicular spacesuit of the U.S.[J]. Manned Spaceflight, 2011, 16(3):36-41(in Chinese).
[3] GRAUMANN D W. Research study on instrument unit thermal conditioning heat sink concepts annual report:NAS8-11291[R]. Washington, D.C.:NASA, 1968.
[4] TONGUE S, DINGELL C W. The porous plate sublimator as the X-38/CRV (Crew Return Vehicle) orbital heat sink[C]//27th International Conference on Environmental Systems, 1997:1-5.
[5] LEWIS J F, BARIDO R A. Crew exploration vehicle environmental control and life support development status:AIAA-2010-6154[R]. Reston, VA:AIAA, 2010.
[6] SKOOG A I, ABRAMOV I P, STOKLITSKY A Y, et al. The Soviet-Russian space suits a historical overview of the 1960's[J]. Acta Astronautic, 2002, 51(1-9):113-131.
[7] METTS J G, KLAUS D M. Equivalent system mass analysis for space suit thermal control:AIAA-2011-5180[R]. Reston, VA:AIAA, 2011.
[8] Hamilton Standard, Windsor Locks, Conn. Phase 1 engineering and technical data report for the thermal control extravehicular life support system:N75-24360[R]. 1975.
[9] CHAPMAN A J. A fundamental study of sublimation through a porous surface:NASA 9-7969[R]. Washington, D.C.:NASA, 1971.
[10] LEIMKUEHLER T O, ANDERSON M S,WESTHEIMER D T. Development of a contaminant insensitive sublimator[C]//36th International Conference on Environmental Systems, 2006.
[11] SHETH R B, STEPHAN R A, LEIMKUEHLER T O. Testing and model correlation of sublimator driven coldplate coupons and EDU[C]//39th International Conference on Environmental Systems, 2009.
[12] 吴志强, 袁修干, 沈力平. 水升华器散热系统分析[J]. 航空学报, 1999, 20(Suppl.):17-19. WU Z Q, YUAN X G, SHEN L P. Analysis of water sublimator heat rejection systems[J]. Acta Aeronautica et Astronautica Sinica, 1999, 20(Suppl.):17-19(in Chinese).
[13] 吴志强, 袁修干, 韩力军, 等. 多孔板水升华器试验研究[J]. 中国空间科学技术, 2000, 20(2):54-60. WU Z Q, YUAN X G, HAN L J, et al. An experimental investigation on porous plate water sublimator[J]. Chinese Space Science and Technology, 2000, 20(2):54-60(in Chinese).
[14] 吴志强, 袁修干. 多孔板水升华器在恒热流条件下的试验研究[J]. 北京航空航天大学学报, 2000, 26(5):552-555. WU Z Q, YUAN X G. Experimental investigation on porous plate water sublimator under constant heat flux[J]. Journal of Beijing University of Aeronautics and Astronautics, 2000, 26(5):552-555(in Chinese).
[15] 吴志强, 沈力平. 憎水涂层多孔板对水升华器散热性能影响的实验研究[J]. 航天医学与医学工程, 2003, 16(4):287-291. WU Z Q, SHEN L P. Experimental research on the effects of hydrophobic coating porous plates on heat dissipation of water sublimator[J]. Space Medicine & Medical Engineering, 2003, 16(4):287-291(in Chinese).
[16] WANG Y Y, ZHONG Q, NING X W, et al. Transient study about the heat transfer of sublimator combined with fluid loop[C]//64th International Astronautical Congress, 2013.
[17] 王玉莹, 钟奇, 宁献文, 等. 具有恒热流边界的水升华器启动特性实验[J]. 航空学报, 2014, 35(6):1571-1580. WANG Y Y, ZHONG Q, NING X W, et al. Experiment on startup performance of sublimator with constant heat flux boundary[J]. Acta Aeronautica et Astronautica Sinica, 2014, 35(6):1571-1580(in Chinese).
[18] WANG Y Y, ZHONG Q, LI J D, et al. Numerical and experimental study on the heat and mass transfer of porous plate water sublimator with constant heat flux boundary condition[J]. Applied Thermal Engineering, 2014, 67:469-479.
[19] 刘畅, 苗建印, 何江, 等. 结构参数对水升华器散热性能影响的研究[J]. 航天器工程, 2016, 25(3):57-62. LIU C, MIAO J Y, HE J, et al. Research on effects of structure parameters on heat dissipation of water sublimator[J]. Spacecraft Engineering, 2016, 25(3):57-62(in Chinese).
[20] 王建永, 汤慧萍, 朱纪磊, 等. 孔隙度对烧结不锈钢纤维多孔材料压缩性能的影响[J]. 粉末冶金技术, 2009,27(5):323-326. WANG J Y, TANG H P, ZHU J L, et al. Effect of porosity on compressive properties of porous sintered stainless steel fiber media[J]. Powder Metallurgy Technology, 2009, 27(5):323-326(in Chinese).
[21] 许飞, 焦磊, 张娟. 烧结316L不锈钢粉末多孔材料拉伸性能的研究[J]. 西安文理学院学报:自然科学版, 2012, 15(3):61-65. XU F, JIAO L, ZHANG J. A study on tensile properties of sintered 316L stainless steel powder porous materials[J]. Journal of Xi'an University of Arts & Science:Natural Science Edition, 2012, 15(3):61-65(in Chinese).
[22] 许飞, 焦磊, 张娟. 烧结316L不锈钢粉末多孔材料压缩性能的研究[J]. 西安文理学院学报:自然科学版, 2015, 18(2):83-87. XU F, JIAO L, ZHANG J. Research on compression properties of sintered 316L stainless steel powders porous materials[J]. Journal of Xi'an University of Arts & Science:Natural Science Edition, 2015, 18(2):83-87(in Chinese).
[23] 白莉, 王有镗, 高青, 等. 地下换热管土结构冻胀变形模拟[J]. 农业工程学报, 2016, 32(18):118-124. BAI L, WANG Y T, GAO Q, et al. Simulation on underground pipe-soil heat exchange structure deformation due to frost heave[J]. Transactions of the Chinese Society of Agricultural Engineering, 2016, 32(18):118-124(in Chinese).
[24] 康永水, 刘泉声, 赵军, 等. 岩石冻胀变形特征及寒区隧道冻胀变形模拟[J]. 岩石力学与工程学报, 2012, 31(12):2518-2526. KANG Y S, LIU Q S, ZHAO J, et al. Research on frost deformation characteristics of rock and simulation of tunnel frost deformation in cold region[J]. Chinese Journal of Rock Mechanics and Engineering, 2012, 31(12):2518-2526(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

多孔板结冰自强化效应对水升华器性能的影响

Influence of self-strengthening effect of porous plate icing on water sublimators' performance

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈勇, 孔维梁, 刘洪. 飞机过冷大水滴结冰气象条件运行设计挑战[J]. 航空学报, 2023, 44(1): 626973-626973.
[2]	黄雄, 曲仕茹, 张恒, 陈显调. 大型客机增升构型缝翼除冰状态失速特性[J]. 航空学报, 2023, 44(1): 627077-627077.
[3]	张恒, 李杰, 赵宾宾. 结冰翼型前缘下垂变弯度容冰特性改善机制[J]. 航空学报, 2023, 44(1): 627114-627114.
[4]	束珺, 徐东光, 韩志熔, 李斯, 黄雄. 结冰风洞过冷大水滴试验中混合翼设计[J]. 航空学报, 2023, 44(1): 627182-627182.
[5]	赵宾宾, 张恒, 李杰. 翼型结冰状态复杂分离流动数值模拟综述[J]. 航空学报, 2023, 44(1): 627211-627211.
[6]	马乙楗, 柴得林, 王强, 易贤, 孔满昭. 翼面结冰过程中的冰晶运动相变与黏附特性[J]. 航空学报, 2023, 44(1): 627817-627817.
[7]	牛俊杰, 桑为民, 李栋, 郝莲, 王泽林. 一种基于水滴收集量代理模型的结冰试飞空域确定方法[J]. 航空学报, 2023, 44(1): 627697-627697.
[8]	郭琪磊, 桑为民, 牛俊杰, 袁烨. 复杂气象条件下考虑结冰风险的无人机飞行策略[J]. 航空学报, 2023, 44(1): 627518-627518.
[9]	伍强, 徐浩军, 魏扬, 裴彬彬, 薛源. 结冰条件下飞机气动/运动耦合特性[J]. 航空学报, 2022, 43(8): 125566-125566.
[10]	黄平, 卜雪琴, 刘一鸣, 林贵平, 杨坤. 混合相/冰晶条件下的结冰研究综述[J]. 航空学报, 2022, 43(5): 25178-025178.
[11]	王昭力, 曾涛, 周志宏, 陈宇. TVD格式在水滴流场数值模拟中的应用[J]. 航空学报, 2022, 43(12): 627010-627010.
[12]	宁献文, 徐侃, 王玉莹, 蒋凡. 嫦娥五号轻量化泵驱单相流体回路热总线设计及实现[J]. 航空学报, 2022, 43(12): 126292-126292.
[13]	李浩然, 段玉宇, 张宇飞, 陈海昕. 结冰模拟软件AERO-ICE中的关键数值方法[J]. 航空学报, 2021, 42(S1): 726371-726371.
[14]	郭向东, 柳庆林, 刘森云, 王梓旭, 李明. 结冰风洞中过冷大水滴云雾演化特性数值研究[J]. 航空学报, 2020, 41(8): 123655-123655.
[15]	卜雪琴, 李皓, 黄平, 林贵平. 二维机翼混合相结冰数值模拟[J]. 航空学报, 2020, 41(12): 124085-124085.